This page details the deferred shading rendering path. See Wikipedia: deferred shading for an introductory technical overview.
When using deferred shading, there is no limit on the number of lights that can affect a GameObject. All lights are evaluated per-pixel, which means that they all interact correctly with normal maps, etc. Additionally, all lights can have cookies and shadows.
Deferred shading has the advantage that the processing overhead of lighting is proportional to the number of pixels the light shines on. This is determined by the size of the light volume in the Scene regardless of how many GameObjects it illuminates. Therefore, performance can be improved by keeping lights small. Deferred shading also has highly consistent and predictable behaviour. The effect of each light is computed per-pixel, so there are no lighting computations that break down on large triangles.
On the downside, deferred shading has no real support for anti-aliasing and can’t handle semi-transparent GameObjects (these are rendered using forward rendering). There is also no support for the Mesh Renderer’s Receive Shadows flag and culling masks are only supported in a limited way. You can only use up to four culling masks. That is, your culling layer mask must at least contain all layers minus four arbitrary layers, so 28 of the 32 layers must be set. Otherwise you get graphical artifacts.
It requires a graphics card with Multiple Render Targets (MRT), Shader Model 3.0 (or later) and support for Depth render textures. Most PC graphics cards made after 2006 support deferred shading, starting with GeForce 8xxx, Radeon X2400, Intel G45.
On mobile, deferred shading is supported on all devices running at least OpenGL ES 3.0.
Note: Deferred rendering is not supported when using Orthographic projection. If the Camera’s projection mode is set to Orthographic, the Camera falls back to Forward rendering.
The rendering overhead of realtime lights in deferred shading is proportional to the number of pixels illuminated by the light and not dependent on Scene complexity. So small point or spot lights are very cheap to render and if they are fully or partially occluded by Scene GameObjects then they are even cheaper.
Of course, lights with shadows are much more expensive than lights without shadows. In deferred shading, shadow-casting GameObjects still need to be rendered once or more for each shadow-casting light. Furthermore, the lighting shader that applies shadows has a higher rendering overhead than the one used when shadows are disabled.
Objects with Shaders that do not support deferred shading are rendered after deferred shading is complete, using the forward rendering path.
The default layout of the render targets (RT0 - RT4) in the geometry buffer (g-buffer) is listed below. Data types are placed in the various channels of each render target. The channels used are shown in parentheses.
So the default g-buffer layout is 160 bits/pixel (non-HDR) or 192 bits/pixel (HDR).
If using the Shadowmask or Distance Shadowmask modes for Mixed lighting, a fifth target is used:
And thus the g-buffer layout is 192 bits/pixel (non-HDR) or 224 bits/pixel (HDR).
If the hardware does not support five concurrent rendertargets then objects using shadowmasks will fallback to the forward rendering path. Emission+lighting buffer (RT3) is logarithmically encoded to provide greater dynamic range than is usually possible with an ARGB32 texture, when the Camera is not using HDR.
Note that when the Camera is using HDR rendering, there’s no separate rendertarget being created for Emission+lighting buffer (RT3); instead the rendertarget that the Camera renders into (that is, the one that is passed to the image effects) is used as RT3.
The g-buffer pass renders each GameObject once. Diffuse and specular colors, surface smoothness, world space normal, and emission+ambient+reflections+lightmaps are rendered into g-buffer textures. The g-buffer textures are setup as global shader properties for later access by shaders (CameraGBufferTexture0 .. CameraGBufferTexture3 names).
The lighting pass computes lighting based on g-buffer and depth. Lighting is computed in screen space, so the time it takes to process is independent of Scene complexity. Lighting is added to the emission buffer.
Point and spot lights that do not cross the Camera’s near plane are rendered as 3D shapes, with the Z buffer’s test against the Scene enabled. This makes partially or fully occluded point and spot lights very cheap to render. Directional lights and point/spot lights that cross the near plane are rendered as fullscreen quads.
Если у источника света включены тени, то они тоже рендерятся и применяются в этом проходе. Учтите, что тени не даются “даром”; требуется рендеринг отбрасывающих тень объектов и к ним должен применяться шейдер с более сложным расчётом освещения.
The only lighting model available is Standard. If a different model is wanted you can modify the lighting pass shader, by placing the modified version of the Internal-DeferredShading.shader file from the Built-in shaders into a folder named “Resources” in your “Assets” folder. Then open the Graphics settings (menu: Edit > Project Settings, then click the Graphics category). Change the “Deferred” dropdown to “Custom Shader”. Then change the Shader option which appears to the shader you are using.
2017–06–08 Page published
Light Modes (Shadowmask and Distance Shadowmask) added in 5.6