Version: 2019.1
Duplicating clips
Splitting clips

Trimming clips

Trimming a clip cuts off a portion of the clip at its start or end. To trim a clip, select the Mix mode as the Clip Edit mode, then drag the start or end of the clip. Dragging the start or end of a clip automatically selects the clip, showing its properties in the Inspector window. Use the Clip Timing properties in the Inspector window to set the start, end, duration, and offset (Clip In) of a clip to exact values.

通过在 Inspector 窗口中调整剪辑的 Start、End、Duration 和 Clip In 属性来定位和修剪剪辑
通过在 Inspector 窗口中调整剪辑的 Start、End、Duration 和 Clip In 属性来定位和修剪剪辑

Trimming the start of a clip

Trimming an Animation clip or Audio clip after the start of the Source Asset, selects the part of the Source Asset the clip uses.

Trimming the start of an Animation clip trims its key animation, relative to the start of the Source Asset
Trimming the start of an Animation clip trims its key animation, relative to the start of the Source Asset

修剪剪辑没有破坏性。再次修剪剪辑可修改其开头,从而包含上次修剪过程剪切掉的动画或音频波形。还可以重置剪辑来撤销修剪操作或其他编辑操作。

To trim the start of a clip to a precise time or frame, use the Clip In property in the Inspector window.

Changing the Clip In property is similar to the same effect as trimming the start of a clip after the start of its Source Asset.

Trimming the end of a clip

As with the start of the clip, trimming an Animation clip or Audio clip before the end of the Source Asset, selects the part of the Source Asset the clip uses.

Trimming the end of an Animation clip trims its key animation, relative to the end of the Source Asset
Trimming the end of an Animation clip trims its key animation, relative to the end of the Source Asset

If you trim the end of an Animation clip or Audio clip past the end of the Source Asset the clip is based on, the extra clip area either holds or loops, depending on the settings of the Source Asset.

For example, an Animation clip named “End Move” uses the motion file “Recorded(2)” as its Source Asset. The motion file “Recorded(2)” is set to loop. Trimming the end of the Animation clip past the end of the “Recorded(2)” Source Asset fills the extra clip area by looping “Recorded(2)”. A white animation curve shows the hold or loop.

A white animation curve indicates whether the extra clip area holds or loops data, depending on the Source Asset
A white animation curve indicates whether the extra clip area holds or loops data, depending on the Source Asset

To choose whether the extra clip area holds or loops, select the Source Asset to change its settings in the Inspector window. Depending on the type of Source Asset, different properties control whether the Source Asset holds or loops.

If you are unsure which Source Asset is used by a clip, select the clip in the Clips view, right-click and select Find Source Asset from the context menu. This highlights the Source Asset in the Project window.

Trimming the end of looping clips

The Timeline window provides special trimming options for Animation clips or Audio clips with loops. These special trim options either remove the last partial loop or complete the last partial loop.

For example, the Animation clip named run_away is over three times longer than the Source Asset on which it is based. Since the Source Asset is set to loop, the Animation clip loops the Source Asset until the Animation clip ends which results in a partial loop.

L1、L2 和 L3 表示完整循环。剪辑结束时,第四次循环 L4 只进行了一部分。
L1、L2 和 L3 表示完整循环。剪辑结束时,第四次循环 L4 只进行了一部分。

To extend the end of the clip and complete a partial loop, select the clip, right-click and select Editing > Complete Last Loop. To trim the clip at the last complete loop, select the clip, Right-clip and select Editing > Trim Last Loop.

选择 Editing > Complete Last Loop 产生的结果
选择 Editing > Complete Last Loop 产生的结果
选择 Editing > Trim Last Loop 产生的结果
选择 Editing > Trim Last Loop 产生的结果

Trimming with the Timeline Playhead

You can also trim a clip based on the location of the playhead. To trim using the playhead, position the playhead within the clip to be trimmed. Right-click the clip and select either Editing > Trim Start or Editing > Trim End. Trim Start trims the start of the clip to the playhead. Trim End trims the end of the clip to the playhead.

在剪辑中移动时间轴播放头
在剪辑中移动时间轴播放头
右键单击并选择 Editing > Trim Start 将剪辑的开头修剪到播放头
右键单击并选择 Editing > Trim Start 将剪辑的开头修剪到播放头

If you select clips on multiple tracks, Timeline only trims the selected clips that intersect the playhead.


  • 2019–08–20 页面已发布并只进行了有限的编辑审查
Duplicating clips
Splitting clips