Audio Source

The Audio Source plays back an Audio Clip in the scene. If the Audio Clip is a 3D clip, the source is played back at a given position and will attenuate over distance. The audio can be spread out between speakers (stereo to 7.1) (Spread) and morphed between 3D and 2D (PanLevel). This can be controlled over distance with falloff curves. Also, if the listener is within one or multiple Reverb Zones, reverberations is applied to the source. (PRO only) Individual filters can be applied to each audio source for an even richer audio experience. See Audio Effects for more details.

The Audio Source gizmo in the Scene View and its settings in the inspector.

Properties


Audio Clip	Reference to the sound clip file that will be played.
Mute	If enabled the sound will be playing but muted.
Bypass Effects	This Is to quickly "by-pass" filter effects applied to the audio source. An easy way to turn all effects on/off.
Play On Awake	If enabled, the sound will start playing the moment the scene launches. If disabled, you need to start it using the Play() command from scripting.
Loop	Enable this to make the Audio Clip loop when it reaches the end.
Priority	Determines the priority of this audio source among all the ones that coexist in the scene. (Priority: 0 = most important. 256 = least important. Default = 128.). Use 0 for music tracks to avoid it getting occasionally swapped out.
Volume	How loud the sound is at a distance of one world unit (one meter) from the Audio Listener.
Pitch	Amount of change in pitch due to slowdown/speed up of the Audio Clip. Value 1 is normal playback speed.
3D Sound Settings	Settings that are applied to the audio source if the Audio Clip is a 3D Sound.
Pan Level	Sets how much the 3d engine has an effect on the audio source.
Spread	Sets the spread angle to 3d stereo or multichannel sound in speaker space.
Doppler Level	Determines how much doppler effect will be applied to this audio source (if is set to 0, then no effect is applied).
Min Distance	Within the MinDistance, the sound will stay at loudest possible. Outside MinDistance it will begin to attenuate. Increase the MinDistance of a sound to make it 'louder' in a 3d world, and decrease it to make it 'quieter' in a 3d world.
Max Distance	The distance where the sound stops attenuating at. Beyond this point it will stay at the volume it would be at MaxDistance units from the listener and will not attenuate any more.
Rolloff Mode	How fast the sound fades. The higher the value, the closer the Listener has to be before hearing the sound.(This is determined by a Graph).
Logarithmic Rolloff	The sound is loud when you are close to the audio source, but when you get away from the object it decreases significantly fast.
Linear Rolloff	The further away from the audio source you go, the less you can hear it.
Custom Rolloff	The sound from the audio source behaves accordingly to how you set the graph of roll offs.
2D Sound Settings	Settings that are applied to the audio source if the Audio clip is a 2D Sound.
Pan 2D	Sets how much the engine has an effect on the audio source.

Types of Rolloff

There are three Rolloff modes: Logarithmic, Linear and Custom Rolloff. The Custom Rolloff can be modified by modifying the volume distance curve as described below. If you try to modify the volume distance function when it is set to Logarithmic or Linear, the type will automatically change to Custom Rolloff.

Rolloff Modes that an audio source can have.

Distance Functions

There are several properties of the audio that can be modified as a function of the distance between the audio source and the audio listener.

Volume: Amplitude(0.0 - 1.0) over distance.
Pan: Left(-1.0) to Right(1.0) over distance.
Spread: Angle (degrees 0.0 - 360.0) over distance.
Low-Pass (only if LowPassFilter is attached to the AudioSource): Cutoff Frequency (22000.0-10.0) over distance.

Distance functions for Volume, Pan, Spread and Low-Pass audio filter. The current distance to the Audio Listener is marked in the graph.

To modify the distance functions, you can edit the curves directly. For more information, see the guide to Editing Curves.

Creating Audio Sources

Audio Sources don't do anything without an assigned Audio Clip. The Clip is the actual sound file that will be played back. The Source is like a controller for starting and stopping playback of that clip, and modifying other audio properties.

To create a new Audio Source:

Import your audio files into your Unity Project. These are now Audio Clips.
Go to GameObject->Create Empty from the menubar.
With the new GameObject selected, select Component->Audio->Audio Source.
Assign the Audio Clip property of the Audio Source Component in the Inspector.

Note: If you want to create an Audio Source just for one Audio Clip that you have in the Assets folder then you can just drag that clip to the scene view - a GameObject with an Audio Source component will be created automatically for it. Dragging a clip onto on existing GameObject will attach the clip along with a new Audio Source if there isn't one already there. If the object does already have an Audio Source then the newly dragged clip will replace the one that the source currently uses.

Platform specific details

iOS

On mobile platforms compressed audio is encoded as MP3 for speedier decompression. Beware that this compression can remove samples at the end of the clip and potentially break a "perfect-looping" clip. Make sure the clip is right on a specific MP3 sample boundary to avoid sample clipping - tools to perform this task are widely available. For performance reasons audio clips can be played back using the Apple hardware codec. To enable this, check the "Use Hardware" checkbox in the import settings. See the Audio Clip documentation for more details.

Android

Page last updated: 2013-07-12