ConfigurableJoint

class in UnityEngine

Inherits from: Joint

Description

The configurable joint is an extremely flexible joint giving you complete control over rotation and linear motion.

You can build all other joints with it and much more but it is also more complicated to setup. It gives you control over motors, drives and joint limits for each rotation axis and and linear degree of freedom.

Variables

angularXDrive	Definition of how the joint's rotation will behave around its local X axis. Only used if Rotation Drive Mode is Swing & Twist.
angularXLimitSpring	The configuration of the spring attached to the angular X limit of the joint.
angularXMotion	Allow rotation around the X axis to be Free, completely Locked, or Limited according to Low and High Angular XLimit.
angularYLimit	Boundary defining rotation restriction, based on delta from original rotation.
angularYMotion	Allow rotation around the Y axis to be Free, completely Locked, or Limited according to Angular YLimit.
angularYZDrive	Definition of how the joint's rotation will behave around its local Y and Z axes. Only used if Rotation Drive Mode is Swing & Twist.
angularYZLimitSpring	The configuration of the spring attached to the angular Y and angular Z limits of the joint.
angularZLimit	Boundary defining rotation restriction, based on delta from original rotation.
angularZMotion	Allow rotation around the Z axis to be Free, completely Locked, or Limited according to Angular ZLimit.
configuredInWorldSpace	If enabled, all Target values will be calculated in world space instead of the object's local space.
highAngularXLimit	Boundary defining upper rotation restriction, based on delta from original rotation.
linearLimit	Boundary defining movement restriction, based on distance from the joint's origin.
linearLimitSpring	The configuration of the spring attached to the linear limit of the joint.
lowAngularXLimit	Boundary defining lower rotation restriction, based on delta from original rotation.
projectionAngle	Set the angular tolerance threshold (in degrees) for projection.If the joint deviates by more than this angle around its locked angular degrees of freedom, the solver will move the bodies to close the angle.Setting a very small tolerance may result in simulation jitter or other artifacts.Sometimes it is not possible to project (for example when the joints form a cycle).
projectionDistance	Set the linear tolerance threshold for projection.If the joint separates by more than this distance along its locked degrees of freedom, the solver will move the bodies to close the distance.Setting a very small tolerance may result in simulation jitter or other artifacts.Sometimes it is not possible to project (for example when the joints form a cycle).
projectionMode	Brings violated constraints back into alignment even when the solver fails. Projection is not a physical process and does not preserve momentum or respect collision geometry. It is best avoided if practical, but can be useful in improving simulation quality where joint separation results in unacceptable artifacts.
rotationDriveMode	Control the object's rotation with either X & YZ or Slerp Drive by itself.
secondaryAxis	The joint's secondary axis.
slerpDrive	Definition of how the joint's rotation will behave around all local axes. Only used if Rotation Drive Mode is Slerp Only.
swapBodies	If enabled, the two connected rigidbodies will be swapped, as if the joint was attached to the other body.
targetAngularVelocity	This is a Vector3. It defines the desired angular velocity that the joint should rotate into.
targetPosition	The desired position that the joint should move into.
targetRotation	This is a Quaternion. It defines the desired rotation that the joint should rotate into.
targetVelocity	The desired velocity that the joint should move along.
xDrive	Definition of how the joint's movement will behave along its local X axis.
xMotion	Allow movement along the X axis to be Free, completely Locked, or Limited according to Linear Limit.
yDrive	Definition of how the joint's movement will behave along its local Y axis.
yMotion	Allow movement along the Y axis to be Free, completely Locked, or Limited according to Linear Limit.
zDrive	Definition of how the joint's movement will behave along its local Z axis.
zMotion	Allow movement along the Z axis to be Free, completely Locked, or Limited according to Linear Limit.

Inherited members

Variables

gameObject	The game object this component is attached to. A component is always attached to a game object.
tag	The tag of this game object.
transform	The Transform attached to this GameObject.
anchor	The Position of the anchor around which the joints motion is constrained.
autoConfigureConnectedAnchor	Should the connectedAnchor be calculated automatically?
axis	The Direction of the axis around which the body is constrained.
breakForce	The force that needs to be applied for this joint to break.
breakTorque	The torque that needs to be applied for this joint to break.
connectedAnchor	Position of the anchor relative to the connected Rigidbody.
connectedBody	A reference to another rigidbody this joint connects to.
enableCollision	Enable collision between bodies connected with the joint.
enablePreprocessing	Toggle preprocessing for this joint.
hideFlags	Should the object be hidden, saved with the scene or modifiable by the user?
name	The name of the object.

Public Functions

BroadcastMessage	Calls the method named methodName on every MonoBehaviour in this game object or any of its children.
CompareTag	Is this game object tagged with tag ?
GetComponent	Returns the component of Type type if the game object has one attached, null if it doesn't.
GetComponentInChildren	Returns the component of Type type in the GameObject or any of its children using depth first search.
GetComponentInParent	Returns the component of Type type in the GameObject or any of its parents.
GetComponents	Returns all components of Type type in the GameObject.
GetComponentsInChildren	Returns all components of Type type in the GameObject or any of its children.
GetComponentsInParent	Returns all components of Type type in the GameObject or any of its parents.
SendMessage	Calls the method named methodName on every MonoBehaviour in this game object.
SendMessageUpwards	Calls the method named methodName on every MonoBehaviour in this game object and on every ancestor of the behaviour.
GetInstanceID	Returns the instance id of the object.
ToString	Returns the name of the game object.

Static Functions

Destroy	Removes a gameobject, component or asset.
DestroyImmediate	Destroys the object obj immediately. You are strongly recommended to use Destroy instead.
DontDestroyOnLoad	Makes the object target not be destroyed automatically when loading a new scene.
FindObjectOfType	Returns the first active loaded object of Type type.
FindObjectsOfType	Returns a list of all active loaded objects of Type type.
Instantiate	Returns a copy of the object original.

Operators

bool	Does the object exist?
operator !=	Compares if two objects refer to a different object.
operator ==	Compares two object references to see if they refer to the same object.

Messages

OnJointBreak

Called when a joint attached to the same game object broke.

Scripting API

ConfigurableJoint

Success!

Sumbission failed

Description

Variables

Inherited members

Variables

Public Functions

Static Functions

Operators

Messages

Script language

Scripting API

ConfigurableJoint

Success!

Sumbission failed

Description

Variables

Inherited members

Variables

Public Functions

Static Functions

Operators

Messages