Version: 2022.1
LanguageEnglish
  • C#
Experimental: this API is experimental and might be changed or removed in the future.

NavMeshQuery.GetEdgesAndNeighbors

Suggest a change

Success!

Thank you for helping us improve the quality of Unity Documentation. Although we cannot accept all submissions, we do read each suggested change from our users and will make updates where applicable.

Close

Submission failed

For some reason your suggested change could not be submitted. Please <a>try again</a> in a few minutes. And thank you for taking the time to help us improve the quality of Unity Documentation.

Close

Cancel

Declaration

public Experimental.AI.PathQueryStatus GetEdgesAndNeighbors(Experimental.AI.PolygonId node, NativeSlice<Vector3> edgeVertices, NativeSlice<PolygonId> neighbors, NativeSlice<byte> edgeIndices, out int verticesCount, out int neighborsCount);

Parameters

node Identifier of a node from a NavMesh surface, NavMeshLink or Off-mesh Link for which the vertices and neighbors need to be retrieved.
edgeVertices The result buffer that contains the world positions describing the geometry of the input navigation node. It can have zero capacity.
Polygonal nodes of the NavMesh have a minimum of 3 and a maximum of 6 vertices.
OffMeshConnection nodes are always represented by 4 vertices, regardless of their width.
neighbors The result buffer that holds the identifiers of all the navigation nodes immediately reachable from the given node. It can have zero capacity.
edgeIndices The helper result buffer that maps each neighbor node to an edge of the given node. It can have zero capacity.
The index of an element in edgeIndices is also an index in the neighbors array and the value of that edgeIndices element is an index in the edgeVertices array.
verticesCount The total number of vertices that describe the geometry of the input node. This is independent of the capacity of the vertices result buffer.
neighborsCount The total number of navigation nodes the input node connects to. This is independent of the capacity of the result buffers (neighbors and edgeIndices).

Returns

PathQueryStatus Success if Unity can evaluate the neighbors and vertices of the specified node, regardless of the result. The verticesCount and neighborsCount are always valid in this case.
Failure if Unity can not use the node identifier to retrieve the neighbors or geometry information. Unity does not modify any of the five result parameters (edgeVertices, neighbors, edgeIndices, verticesCount or neighborsCount) in this case.
InvalidParam is part of the returned flags if the specified navigation node is not valid in the query's NavMeshWorld.
BufferTooSmall is part of the PathQueryStatus flags, that Unity returns from this function, when any of the result buffers you provide are not large enough to hold all the neighbor nodes the input node connects to or all of its edge vertices.

Description

Retrieves the vertices of a given node and the identifiers of all the navigation nodes to which it connects.

A polygon of a NavMesh surface connects to all other neighboring polygons with which it shares an edge as well as all the OffMeshLinks or NavMeshLinks that leave from anywhere on its surface. The polygon does not connect to other polygons with which it shares only a vertex.
Each point returned in the edgeVertices array represents the start of a node's edge and the subsequent element in the array is the end point of that edge. All vertices form a closed polygonal line. The last and first elements define the last edge.

An off-mesh link connects to all the NavMesh polygons that each end of the link intersects with, regardless of whether the link is unidirectional.
For link nodes the returned edgeVertices array contains two pairs of points at indices [0]-[1] and [2]-[3] that define the end points of the start and end edges of the link, in this order. These are the world positions established at the moment when the link is instantiated in the NavMesh world. For nodes added through Off-mesh Link components the pairs contain the same value in both of their elements.

A node from the neighbors array lies at the edge returned in edgeIndices at the same index.
If both the given node and its neighbor are NavMesh polygons, then the corresponding edgeIndices value represents the index of the polygon edge that leads from node to the neighbor. E.g. edgeVertices[edgeIndices[2]] represents the start point of the edge that is common between node and the neighbors[2] node, and edgeVertices[edgeIndices[2] + 1] is the end point of that edge.
A NavMesh polygon can have a maximum of 6 edges. This means the edgeIndices value corresponding to a polygon-polygon connection is between 0 and 5, inclusive. An edge usually connects only the two polygons that share it, but edges that sit at a tile border can connect one polygon in the first tile to multiple polygons in the second tile. In this case, edgeIndices report the same value for all of those neighbors.
If either the given node or the neighbor is a link, then the corresponding edgeIndices value represents the side on the link where the connection is made: 0 for start and 2 for end. When the node is a polygon and the neighbor is a link the value acts only as information about the side of the link where the two nodes connect and should not be used as an index in the edgeVertices array.
When the neighbors and edgeIndices buffers both have positive capacity, they must be the same size, otherwise you will encounter an ArgumentException when this method executes in the Editor.

You can set any of the buffers to have zero capacity for the cases when you do not need the results.

The returned verticesCount and neighborsCount values express the number of elements that comprise the result in the output buffers of sufficient size. Buffers that are not large enough are still filled with valid nodes up to their full capacity.

The five result parameters (edgeVertices, neighbors, edgeIndices, verticesCount and neighborsCount) do not act as input and do not change the internal navigation data in any way. Unity only modifies them in the case when the operation returns a Success status.

See Also: NavMeshQuery.GetPolygonType, NavMeshQuery.GetPortalPoints.

using Unity.Collections;
using UnityEngine;
using UnityEngine.Experimental.AI;

public class NavMeshNodeEdgesDrawer : MonoBehaviour { void Update() { var query = new NavMeshQuery(NavMeshWorld.GetDefaultWorld(), Allocator.Temp); var vertices = new NativeArray<Vector3>(6, Allocator.Temp); var neighbors = new NativeArray<PolygonId>(10, Allocator.Temp); var edgeIndices = new NativeArray<byte>(neighbors.Length, Allocator.Temp); int totalVertices; int totalNeighbors;

var location = query.MapLocation(transform.position, Vector3.one, 0);

var queryStatus = query.GetEdgesAndNeighbors( location.polygon, vertices, neighbors, edgeIndices, out totalVertices, out totalNeighbors);

var color = (queryStatus & PathQueryStatus.Success) != 0 ? Color.green : Color.red; Debug.DrawLine(transform.position - Vector3.up, transform.position + Vector3.up, color);

for (int i = 0, j = totalVertices - 1; i < totalVertices; j = i++) { Debug.DrawLine(vertices[i], vertices[j], Color.grey); }

for (var i = 0; i < totalNeighbors; i++) { if (query.GetPolygonType(neighbors[i]) == NavMeshPolyTypes.OffMeshConnection) { // The link neighbor is not connected through any of the polygon's edges. // Call GetEdgesAndNeighbors() on this specific neighbor in order to retrieve its edges. continue; }

var start = edgeIndices[i]; var end = (start + 1) % totalVertices; var neighborColor = Color.Lerp(Color.yellow, Color.magenta, 1f * start / (totalVertices - 1)); Debug.DrawLine(vertices[start], vertices[end], neighborColor); }

query.Dispose(); vertices.Dispose(); neighbors.Dispose(); edgeIndices.Dispose(); } }