ShaderLab: Blending

Blending is used to make transparent objects.

When graphics are rendered, after all shaders have executed and all textures have been applied, the pixels are written to the screen. How they are combined with what is already there is controlled by the Blend command.

Syntax

Blend Off: Turn off blending (this is the default)

Blend SrcFactor DstFactor: Configure and enable blending. The generated color is multiplied by the SrcFactor. The color already on screen is multiplied by DstFactor and the two are added together.

Blend SrcFactor DstFactor, SrcFactorA DstFactorA: Same as above, but use different factors for blending the alpha channel.

BlendOp BlendOp: Instead of adding blended colors together, do a different operation on them.

BlendOp OpColor, OpAlpha: Same as above, but use different blend operation for color (RGB) and alpha (A) channels.

AlphaToMask On: Turns on alpha-to-coverage. When MSAA is used, alpha to coverage modifies multisample coverage mask proportionally to the pixel shader result alpha value. This is typically used for less aliased outlines than regular alpha-test; useful for vegetation and other alpha tested shaders.

Blend operations

The following blend operations can be used:

Blend factors

All following properties are valid for both SrcFactor & DstFactor in the Blend command. Source refers to the calculated color, Destination is the color already on the screen. The blend factors are ignored if BlendOp is using logical operations.

Details

Below are the most common blend types:

Blend SrcAlpha OneMinusSrcAlpha // Traditional transparency
Blend One OneMinusSrcAlpha // Premultiplied transparency
Blend One One // Additive
Blend OneMinusDstColor One // Soft Additive
Blend DstColor Zero // Multiplicative
Blend DstColor SrcColor // 2x Multiplicative

Alpha Blending, Alpha Testing, Alpha To Coverage

For drawing mostly fully opaque or fully transparent objects, where transparency is defined by texture’s alpha channel (e.g. leaves, grass, chain fences etc.), several approaches are commonly used:

Alpha Blending

Often this means that objects have to be considered as “semitransparent”, and thus can’t use some of the rendering features (deferred shading; can’t receive shadows etc.). Concave or overlapping alpha blended objects often also have draw ordering issues.

Most often alpha blended shaders also set transparent render queue, and turn off depth writes. So the shader code looks like:

// inside SubShader
Tags { "Queue"="Transparent" "RenderType"="Transparent" "IgnoreProjector"="True" }

// inside Pass
ZWrite Off
Blend SrcAlpha OneMinusSrcAlpha

Alpha Testing / Cutout

By using clip() HLSL instruction in the pixel shader, a pixel can be “discarded” or not based on some criteria. This means that object can still be considered as fully opaque, and has no draw ordering issues. However, this means that all pixels are fully opaque or transparent, leading to aliasing (“jaggies”).

Most often alpha tested shaders also set cutout render queue. So the shader code looks like:

// inside SubShader
Tags { "Queue"="AlphaTest" "RenderType"="TransparentCutout" "IgnoreProjector"="True" }

// inside CGPROGRAM in the fragment shader:
clip(textureColor.a - alphaCutoffValue);

Alpha to Coverage

When using multisample anti-aliasing (MSAA, see QualitySettings), it is possible to improve alpha testing approach by using “alpha to coverage” GPU functionality. This improves edge appearance, depending on the MSAA level used.

This functionality works best on texures that are mostly opaque or transparent, and have very thin “partially transparent” areas (grass, leaves and similar).

Most often alpha-to-coverage shaders also set cutout render queue. So the shader code looks like:

// inside SubShader
Tags { "Queue"="AlphaTest" "RenderType"="TransparentCutout" "IgnoreProjector"="True" }

// inside Pass
AlphaToMask On

Example

Here is a small example shader that adds a texture to whatever is on the screen already:

Shader "Simple Additive" {
    Properties {
        _MainTex ("Texture to blend", 2D) = "black" {}
    }
    SubShader {
        Tags { "Queue" = "Transparent" }
        Pass {
            Blend One One
            SetTexture [_MainTex] { combine texture }
        }
    }
}