ShaderLab: Blending

Blending is used to make transparent objects.

When graphics are rendered, after all shaders have executed and all textures have been applied, the pixels are written to the screen. How they are combined with what is already there is controlled by the Blend command.

Syntax

Blend Off: Turn off blending

Blend SrcFactor DstFactor: Configure & enable blending. The generated color is multiplied by the SrcFactor. The color already on screen is multiplied by DstFactor and the two are added together.

Blend SrcFactor DstFactor, SrcFactorA DstFactorA: Same as above, but use different factors for blending the alpha channel.

BlendOp BlendOp: Instead of adding blended colors together, do a different operation on them.

Blend operations

The following blend operations can be used:

Add	Add source and destination together.
Sub	Subtract destination from source.
RevSub	Subtract source from destination.
Min	Use the smaller of source and destination.
Max	Use the larger of source and destination.
LogicalClear	Logical operation: Clear (0) DX11.1 only.
LogicalSet	Logical operation: Set (1) DX11.1 only.
LogicalCopy	Logical operation: Copy (s) DX11.1 only.
LogicalCopyInverted	Logical operation: Copy inverted (!s) DX11.1 only.
LogicalNoop	Logical operation: Noop (d) DX11.1 only.
LogicalInvert	Logical operation: Invert (!d) DX11.1 only.
LogicalAnd	Logical operation: And (s & d) DX11.1 only.
LogicalNand	Logical operation: Nand !(s & d) DX11.1 only.
LogicalOr	Logical operation: Or (s | d) DX11.1 only.
LogicalNor	Logical operation: Nor !(s | d) DX11.1 only.
LogicalXor	Logical operation: Xor (s ^ d) DX11.1 only.
LogicalEquiv	Logical operation: Equivalence !(s ^ d) DX11.1 only.
LogicalAndReverse	Logical operation: Reverse And (s & !d) DX11.1 only.
LogicalAndInverted	Logical operation: Inverted And (!s & d) DX11.1 only.
LogicalOrReverse	Logical operation: Reverse Or (s | !d) DX11.1 only.
LogicalOrInverted	Logical operation: Inverted Or (!s | d) DX11.1 only.

Blend factors

All following properties are valid for both SrcFactor & DstFactor in the Blend command. Source refers to the calculated color, Destination is the color already on the screen. The blend factors are ignored if BlendOp is using logical operations.

One	The value of one - use this to let either the source or the destination color come through fully.
Zero	The value zero - use this to remove either the source or the destination values.
SrcColor	The value of this stage is multiplied by the source color value.
SrcAlpha	The value of this stage is multiplied by the source alpha value.
DstColor	The value of this stage is multiplied by frame buffer source color value.
DstAlpha	The value of this stage is multiplied by frame buffer source alpha value.
OneMinusSrcColor	The value of this stage is multiplied by (1 - source color).
OneMinusSrcAlpha	The value of this stage is multiplied by (1 - source alpha).
OneMinusDstColor	The value of this stage is multiplied by (1 - destination color).
OneMinusDstAlpha	The value of this stage is multiplied by (1 - destination alpha).

Details

Below are the most common blend types:

Blend SrcAlpha OneMinusSrcAlpha // Alpha blending
Blend One One // Additive
Blend OneMinusDstColor One // Soft Additive
Blend DstColor Zero // Multiplicative
Blend DstColor SrcColor // 2x Multiplicative

Example

Here is a small example shader that adds a texture to whatever is on the screen already:

Shader "Simple Additive" {
    Properties {
        _MainTex ("Texture to blend", 2D) = "black" {}
    }
    SubShader {
        Tags { "Queue" = "Transparent" }
        Pass {
            Blend One One
            SetTexture [_MainTex] { combine texture }
        }
    }
}